> ## Documentation Index > Fetch the complete documentation index at: https://docs.lagerdata.com/llms.txt > Use this file to discover all available pages before exploring further. # Version 0.61.0 > October 30, 2026 ## Upgrade Notes * **Update your boxes.** Most of the fixes in this release run on the box. Run `lager update --box ` after you upgrade the CLI. * **`lager wifi status` exits 1 when the box has no wireless interface.** It used to print "Interface detection failed" and exit 0. A script that treats that exit as success must now handle the failure. * **`lager wifi status` and `lager wifi access-points` run on the box host over SSH.** They used to run inside the container, which cannot see the host's wireless interface. `access-points` now scans the box's own wireless interface by default, not `wlan0`. * **`lager usb` on a YKUSH hub fails when a port does not switch.** The hub acknowledges a switch that it ignores, and `enable`, `disable`, `toggle` and `cycle` reported success. The driver now reads the port back. A script that relied on the false success now gets an error. ## Features * **Yepkit YKUSH3 hubs are supported.** `lager instruments` and `lager nets add-all` detect the YKUSH3 (`04d8:f11b`). Its three USB ports are `usb` nets for `lager usb`. Its three GPIO pins are `gpio` nets for `lager gpi` and `lager gpo`. The hub's switchable 5V output is not a net. * **The IPEVO V4K PRO document camera (`1778:d00e`) is detected as a webcam.** `lager instruments` lists it, and `lager nets add webcam ...` accepts it. * **A gated box's gateway can see which command each request belongs to.** Requests that carry a `lager login` token also send the command's name, such as `supply voltage`, with the CLI version and an id for the command. The name never includes arguments. A box that is not behind a gateway receives none of these headers. ## Bug Fixes * **The `/scope` page shows the scope's real state.** * A Rigol that loses only its capture card is no longer called unplugged. The page says that the live view stopped, and it says when the card is back. * The page says when the box closes its connection after a long idle. * The run badge shows a dash after a disconnect. It used to keep its last state, such as TRIG'D, until the next frame. * The page says when a scope net has no channel nets, and it gives the `lager nets add` command for each channel. * The stream request no longer returns paths on the box when a scope's daemon fails. * **The `/scope` page draws a Rigol's trace where the scope's own screen does.** * `display zoom` now magnifies the trace and shows the zoom bar. * A channel's hardware offset now moves its trace. The volts read off the trace do not change. * The box checks for a Rigol's side menu again a minute after a check finds none. The menu no longer stays over the live view. * **A `stop` typed in the `/scope` page's console stops the measurement polling.** `start` and `start single` in the console now follow the same rule as their buttons. * **`lager scope cursor move-a` and `move-b` move from where the cursor is.** On a Rigol, each call started from the center of the grid. After `set-a --x -200`, `move-a --x 50` now puts A at -150, not +50. * **`lager scope status` says "running" for a Rigol that the daemon opens while it runs.** The command and the scope page said "stopped" after every daemon restart, power cycle or replug until you pressed Start. * **`lager scope measure` prints a reading without float noise.** A Rigol's duty cycle now prints as `49.987 %`, not `49.986999999999995 %`. A Rigol's refusal of an averaging count no longer names 65536 captures, which the CLI does not accept. * **A Rigol MSO5000 bus decoder is refused before anything is sent.** Creating a UART, I2C, SPI, CAN or FlexRay decoder failed partway through the setup with "Function not found". It now raises an error that says the scope does not decode buses through lager. * **The scope daemon's log says when the capture card stopped.** Requests that wait at that moment are no longer told that the oscilloscope stopped answering. * **The scope daemon notices a PicoScope unplugged while it was idle.** The next command failed with a bare driver error. The daemon now closes the unit when a 2000-series call fails and no PicoScope is on the bus. It opens the unit again when it returns. * **A PicoScope plugged back in gets its settings back.** Channel enables, volts/div, coupling, probe, timebase and trigger returned to the driver's defaults, so a page that pressed Start drew nothing. The same unit, by serial, now keeps its settings. A different unit starts from its defaults. * **`lager debug flash` and `lager debug erase` no longer call an unreachable box too old.** With `--erase-start` or `--erase-size`, a `/health` timeout told you to update the box. The command now retries twice, then says that the box or its Stout gateway did not answer. * **`lager diagnose` on a USB hub net reports an unreachable endpoint as unreachable.** It used to say that the box does not serve `/diagnose/usbhub`, and it told you to update the box. * **`lager usb` says that the box service restarts, not "cannot reach box".** When a hub does not open after it re-enumerates, the box service exits to recover. It now answers first, and it tells you to retry in a few seconds. * **Python API calls on a multi-channel supply net act on that net's channel.** On a Rigol DP800 or Keysight E36000, `ovp()`, `ocp()`, `state()`, `clear_ovp()` and similar calls through `Net.get()` sometimes acted on another channel. `lager supply` was not affected. * **`lager supply` can set OVP and OCP back to a Rigol DP800's factory limits.** A DP800 ships with protection limits up to 110% of the channel's rating, and the CLI refused any limit above the rating. The limit is now 110%. Voltage and current setpoints stay within the rating. * **`wait_for_level()` on a LabJack T7 GPIO net counts the stream setup against its timeout.** A call ran about 30 ms past its timeout. The call still stops the stream before it raises `TimeoutError`, which can take about 0.6 s. * **A command stopped with `kill` releases its box lock.** A killed background command, such as `lager debug gdbserver`, used to hold its lock until the lock's TTL ran out. * **The box's authorized\_keys sync survives the end of an install or update.** The key-sync poller now runs in its own session. A signal to the caller's process group no longer stops it. * **The box image carries the license notices of uldaq and the LabJack Exodriver.** They are at `/usr/share/licenses/lager/vendor/`. ## Known Limitations * **The YKUSH3 GPIO pins are not fully verified on hardware.** Their voltage level, and whether a written level is held, are not yet measured. * **Two IPEVO V4K PRO cameras on one box share an address.** The camera reports no serial. * **I2C and SPI per-call overrides stay on the driver.** An `overrides` value such as `frequency_hz` also applies to later calls on the same net. Set the value that you want on each call. * **A failed resistance set on an EA solar net does not raise an error.** The call returns the resistance that the instrument still has. Compare the returned value with the value you set. ## Installation To install this version: ```bash theme={null} pip install lager-cli==0.61.0 ``` To upgrade from a previous version: ```bash theme={null} pip install --upgrade lager-cli==0.61.0 ``` Then update your boxes: ```bash theme={null} lager update --box ``` ## Resources [View Release on PyPI](https://pypi.org/project/lager-cli/0.61.0/) This documentation is built and hosted on [Mintlify](https://mintlify.com), a developer documentation platform.